How To Fix ESP Bas Light On Jeep Liberty?
So, you purchased the trending Jeep Liberty, and it’s on the roll! But while you drive it with some classic radio song, you see the words ‘ESP Bas’ flashing on the dashboard.
Firstly, you do not know what it means, but that’s not the problem. The problem is you do not know how to turn off the ESP Bas light.
Now, since you do not know what the ESP Bas is, it is quite normal as we’ve seen in other cases that you might take an impulsive action as you spot the ESP Bas flashing. This sure isn’t a wise move.
Hence, let’s not keep you in the dark. The ESP Bas light indicates that something is wrong with the Electronic Stability Program or ESP of your Jeep Liberty. So, How to fix the ESP light on Jeep Liberty?
First, you need to take care of the issue that’s illuminating the ESP Bas, and then it will turn off itself! Not rocket science, but you sure need to know about it. So, let’s do some digging on it and get rolling with the Jeep again!
What is ESP Bas Light?
Before we dig into the possible reasons why the ESP Bas light turns on, why not see what this ESP Bas is.
Out of the several warning lights that can be located on the dashboard of your car, this one you shouldn’t avoid or overlook. When it shows, it usually indicates that your car has an issue that has to be addressed.
In some circumstances, you may have a massive issue on your hands, while in others; you may be able to turn off an ESP BAS light with minimal effort.
In any case, you should not wait too long to in handling the ESP BAS light on your dashboard. In your car, both the brake assist program and the electronic stability program play critical roles.
These features are intended to keep you protected, which is why the ESP BAS light on your dashboard should not be ignored. So, how do you restore the safety and protection of your Jeep?
Well, do a repairing session of whatever is causing that light to come on. And do that soon if you don’t want to sign up for something really bad for the vehicle.
Reasons and Solutions for ESP Bas Light Turned On
Now, as you already know what the ESP Bas light is, you must be wondering what is the one issue that turns on the light.
To your surprise, I have to tell you that it’s not a single issue that makes it come on, but rather there are a bunch of them. So, how are you supposed to figure out which is the issue of your vehicle out of the whole list?
Thankfully, it’s rather simple to accomplish. If you have a code scanner, you may read the diagnostic issue codes from your car to figure out what’s wrong. But even if you don’t have one, nothing to be afraid of, you can simply take the vehicle to a mechanic and they will pull the codes for you as you don’t have access to them.
The codes will disclose what’s wrong with your car and why your ESP BAS light has been illuminated. Several factors can cause the ESP BAS light on your vehicle to turn on and keep flashing. Let’s take a look at them.
1. Steering angle sensor issue
In your car, there is a steering angle sensor or SAS, that is meant to help your steering wheel function in unison with your car’s wheels.
It allows you to turn your automobile to the left or right while driving by just turning your steering wheel. The most typical cause of your ESP Bas light being illuminated is a problem with the steering angle sensor.
A steering angle sensor in your automobile will occasionally stop working, and this will usually result in the ESP BAS light on your dashboard going on. The ESP BAS light will remain to flash until you reset the steering angle sensor, allowing it to resume its function.
So, what happens to be precise? The steering angle sensor determines if your wheel is centered or not. The technique for centering the wheel is to turn it twice to the right, then twice to the left, and lastly back to the center.
The sensor should reset as a result, and the light should go away. However, in some circumstances, this will not work, and you will need to look into other options. Don’t worry, the other issues are pretty simple to fix as well so, you won’t have to reach out to a mechanic! Let’s check them out.
2. Wheel speed sensor issue
Out of the many important tasks your ESP and BAS systems carry out, they keep track of the speed of all four wheels on your automobile to make sure they’re rotating at a similar rate all the time.
If these systems detect that your car’s wheels are spinning at various speeds, they will automatically intervene to get them all spinning at the same pace, enabling you to retain absolute control of your vehicle.
However, they won’t be able to accomplish this if one of your wheels has a defective wheel speed sensor, and your ESP BAS light will illuminate as a result.
As a result, you must replace the wheel speed sensors. There’s no need to break a sweat! It’s not difficult to change the wheel speed sensors.
In the broad scheme of things, they’re also not going to cost you a lot of money. However, you shouldn’t wait and replace them as soon as possible, and make sure your ESP BAS light turns off after you’re done.
3. Raggedy brake pads
Although worn-out brake pads aren’t usually the cause of your ESP BAS light turning on, it’s not unheard of. Your brake pads may change the rate at which your car’s wheels spin in some cases, causing your ESP BAS indicator to illuminate.
Hence, if you find out that the raggedy old brake pads are the reason why the ESP lights are on, don’t wait, and replace them as soon as you can.
Now, if you are a car anatomy expert or have a mechanical degree, you can possibly do the honors yourself but if not, then don’t try experimenting, go to a professional. Once you install the new brake pads correctly, you’ll see how the ESP Bas light turns off without any delay.
4. Defective Brake switch
As you step on the brake pedal in your car, it will immediately begin to slow down. It will also switch on your car’s brake lights to alert others behind you that you’re braking. When you press down on your brake pedal, your braking system activates a brake switch, which turns this light on.
This electrical switch may go bad on you from time to time, and if you’re not careful, it might put you in danger. And how are you supposed to know? That’s when the ESP lights start flashing!
Replacing your car’s brake switch is a pretty simple auto repair that should not take more than a few minutes. In comparison to many other auto repairs, it’s also a fairly low-cost job. However, it will keep you secure and turn off your ESP BAS light as the vehicle is completely fixed and ready for the move again.
How to Turn Off the ESP Bas Light?
Compared to other warnings from the vehicle, turning off the ESP Bas light seems a lot easier and cost-effective, doesn’t it?
All you need to do is find out what is keeping the lights on and off you go to fix it, eventually turning the ESP light off. Although I’ve already told you how to fix the ESP Bas light on the Jeep liberty, Let’s revise.
Step 1:
Use a code scanner to pull out the codes from the main computer of your vehicle. If you do not have a scanner, contact a mechanic.
Step 2:
Find out the car issues which are keeping the light illuminated.
Step 3:
Make arrangements to fix the issues as necessary which can eventually lead to turning off the ESP light.
If you are still worrying, let me tell you, it’s not a matter of days; it will hardly take one or two hours to get the issues fixed and turn off the ESP light, so you can just relax.
Similar Posts:
How to fix Jeep Cherokee Service Shifter
Jeep Backup Camera Black Screen Not Working Fixed
How to Fix Jeep Grand Cherokee Transmission Over Temp Problems