How To Replace Jeep Renegade Key Fob Battery?
If you find that your Jeep Renegade’s key fob is not working properly from a distance, but it works fine when you get closer, then you probably just need to replace the battery. But how do you replace the jeep renegade key fob battery?
Quick Answer: Begin by opening the key fob with a screwdriver. Next, open the battery shaft and remove the old battery. Finally, insert a new CR 2032 battery with the negative side facing down.
So, let’s start by explaining everything you need to know to replace the jeep renegade key fob battery:
How Would I know that my Jeep Renegade Key Fob Needs Battery Replacement?
If you’re wondering how to tell if your Jeep Renegade key fob needs a new battery, here are some things to look out for:
- After you turn the key in your Jeep, it begins to slow down.
- The battery cables have visible corrosion from extended use.
- Connectors also show accumulated wear and tear.
- You may hear a clicking or beeping noise once the key is turned.
- Some electronic devices (Radio, Wiper, Navigation) will still display power but the Jeep itself won’t turn on.
How To Replace Jeep Renegade Key Fob Battery?
Replacing your Jeep Renegade key fob battery is a very accessible, convenient, and easy process that anyone can understand.
It’s also quite inexpensive to replace the battery by yourself and you don’t need to go to a mechanic. Just follow our simple DIY steps below:
Step 1: Detach the Key from Key Fob
There is a metal switch located on the back of your Jeep Renegade Key Fob. Press and hold down the switch to unlock the key from the fob. Next, remove the key from the fob.
Step 2: Get a Flathead Screwdriver
You’ll need to use a flathead screwdriver to open the Key Fob. Insert the blade of the screwdriver into the seam between the two halves of your Jeep Renegade’s key fob and gently pry it apart.
Step 3: Separate the Key Fob
Gently pry the two pieces of the key fob apart with a screwdriver. You may need some force, but don’t bend the plastic too much.
Step 4: Take out the Old battery
Once the two pieces are separated, you’ll be able to see the battery. Carefully remove it from its compartment and discard it properly.
Step 5: Insert New Battery
You will need to purchase a CR2032 battery, we recommend brands like Duracell. Once you have the new battery, install it by making sure the negative side is facing downwards.
After that, close up the Key Fob casing, and congratulations, you’ve just replaced your Jeep Renegade’s key fob batteries! The final step is to reset it.
Do you have to reprogram a key fob after changing the battery?
Typically, you do not need to reprogram the key fob after only changing the batteries. However, if you’ve replaced more than just the batteries-such as some of the internal wiring and electronics-you may need to connect it to your car again.
How much does it cost to replace the battery in a Jeep Renegade key fob?
Replacing the battery in your Jeep Renegade’s key fob typically costs around $5 to $10, depending on where you purchase the batteries.
How do I avoid damaging my Jeep Renegade key fob?
To avoid damaging the key fob, don’t try to force it open with a screwdriver or other tool. Also, make sure to insert the new battery carefully and gently into its compartment.
Make sure to keep your Jeep Renegade key fob protected from moisture, dust, and other debris. The more you take care of it, the longer its battery will last.
What type of battery do I need for my Jeep Renegade key fob?
A CR2032 battery is most commonly used for Jeep Renegade key fobs. They are small and easy to find in most stores.
Why won’t my key fob work after I changed the battery?
For your remote key fob to work, it must be connected to a receiver inside your car. If you change the battery in your key fob and it starts acting funny, that means the connection between has been interrupted and you’ll need to reset it.